Go to page of Go. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities.
|Published (Last):||9 October 2007|
|PDF File Size:||13.38 Mb|
|ePub File Size:||5.11 Mb|
|Price:||Free* [*Free Regsitration Required]|
Important Safety Instructions 1. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth.
Do not block any ventilation openings. Table Of Contents Safety Instructions The Features section on the next page provides a brief overview of the exceptional features of the LSR Series.
Indicates that an LED is lit red. The end result is a product that is nothing short of revolutionary — a monitoring system suitable for use in the most demanding music, broadcast, and postproduction applications. Connect each speaker to a suitable power source using the supplied AC power cable. See page 23 in this manual for more information. Connect the speakers together in any order using the supplied CAT5 cable. Plug one end of the cable into either of the two HiQnet ports on one speaker and the other end into a HiQnet port on another speaker until all speakers are connected.
See page 24 in this manual for a wiring diagram. If you are connecting digital signals i. Quick Start 8. All speakers in the system will power on the JBL Logo will go from dimly to brightly lit. All speakers in the system will go to the designated volume. As the volume is increased, additional LEDs light. Below is a listing and description of each.
Reference - Front Panel 2. Power — After connection to an AC power source, press this button to turn the speaker on. If networked together with other speakers, all speakers will turn on simultaneously.
For more information, see Appendix E on page 38 in this manual. SOLO — Press this button to mute the signal on all other speakers. For more information, see page 25 in this manual.
When the button is lit, EQ is active. Reference - Front Panel 9. For more information, see page 23 in this manual. Reference - Rear Panel Reference - Rear Panel 4. Reference - Remote Control Remote Control The provided infrared wireless remote control allows you to make adjustments to your LSR system without leaving the mix position. The front panel RMC buttons will light. Press again to reactivate RMC settings.
While the exact stereo listening angle is largely a matter of personal preference, we recommend the monitors be arranged to form an equilateral triangle as shown in the illustration below. The ground terminal of the IEC plug is required by wiring codes and regulations. It must always be connected to the electrical installation safety ground. Make sure all LSR monitors are positioned as intended. Using the mic clip, attach the provided calibration microphone to a mic stand and place the mic at the mix position, oriented vertically, at ear level.
Be sure that it is no closer than 1. Position the calibration microphone vertically 3. After pressing the RMC button, move away from the speaker. A complete listing of all parameters for the factory presets is presented in Appendix A. To clear the memory of a speaker and recall the factory EQ presets: 1. Turn the speaker off and disconnect its power cable.
The cabling recommendations given below follow standard wiring practice for differential inputs. Appendix C: Wiring Requirements Unbalanced Sources When using unbalanced sources, there are more possibilities to introduce ground loops into a system. Single conductor cable should be used as a last resort as it provides the greatest likelihood of problems.
Hole Pattern: Caution: Unsafe mounting or overhead suspension of any heavy load can result in serious injury and equipment damage.
You can create a visual reference for any listening distance using a readily-available Sound Pressure Level SPL meter and a pink-noise source. Here is the procedure for doing so: 1. Place the SPL meter at the mix position and turn it on. This Warranty does not apply to JBL products purchased elsewhere except for purchases through military outlets. Other purchasers should contact the local JBL distributor for warranty information.
Page 12 Quick Start 8. Page 14 Reference - Front Panel 2. Page 17 Reference - Front Panel 9. Page 20 Reference - Rear Panel Page 21 Reference - Rear Panel 4. Page 22 Reference - Remote Control Remote Control The provided infrared wireless remote control allows you to make adjustments to your LSR system without leaving the mix position. Page 39 Appendix C: Wiring Requirements Unbalanced Sources When using unbalanced sources, there are more possibilities to introduce ground loops into a system.
Page 51 Part Number: Rev.
JBL LSR4326P - monitor speakers Specs
JBL LSR4326P Manuals
JBL Professional LSR4326P User Manual
JBL LSR34328P LSR4326P Manual